The Key to Successful Brazing

Brazing is defined as a process of joining metals in which, during or after heating, molten filler metal is drawn into or retained in the space between closely adjacent surfaces by capillary attraction. The key words are capillary attraction. Everything you do in brazing — joint design, flux selection, heating technique — is aimed at promoting capillary flow. If capillary flow is not achieved, you are not brazing. You are using an expensive filler rod to block a hole.

This guide covers the fundamentals of the brazing process, from joint design and surface preparation through to flux selection, heating technique and post-braze cleaning. It also includes a troubleshooting section for the most common problems encountered in production and maintenance brazing.

The Fundamentals of Capillary Flow

Capillary action draws molten brazing alloy into a narrow joint gap through surface tension and adhesion between the alloy and the base metal. For capillary action to work effectively, three conditions must be met simultaneously: the base metals must be at or above the alloy liquidus temperature; the flux must be active and the base metal surfaces clean; and the heat distribution in the assembly must direct alloy flow in the desired direction.

The joint gap is the most critical variable. For most silver brazing applications, a gap of 0.05–0.2mm when cold is recommended. Capillary action is strongest at narrow, consistent gaps — wider gaps reduce capillary pull and produce unreliable, porous joints. Design and fixture your joints so that the gap falls within the optimal range at brazing temperature, not just when cold.

  • Lap joints

    The most common and generally strongest joint type for brazing. Load is transferred in shear across the brazed interface. A well-designed lap joint with adequate overlap — at least three times the thickness of the thinner member — will typically fail in the parent metal rather than at the joint.

  • Butt joints

    The least efficient geometry for brazing. Load is transferred in tension, where brazed joints are relatively weak. Avoid butt joints for load-bearing applications. Where unavoidable, use a scarf joint to increase the effective joint area and shift loading towards shear.

  • Tubular joints

    Effectively cylindrical lap joints and the strongest brazed joint geometry relative to material cross-section. A socket depth equal to the tube diameter provides more than adequate strength for most applications.

  • Blind joints

    Avoid where possible. Trapped air creates back-pressure that prevents alloy penetration and can blow flux out of the joint. Where unavoidable, a small vent hole at the blind end allows air to escape.

Surface Preparation and Joint Cleanliness

Joint cleanliness at room temperature matters less than it appears. Oxide removal is the function of the flux — whatever you remove during assembly will be replaced by the heat source before brazing begins. What does matter is that joints are free of oil and grease. Degrease using warm soapy water, solvent or a wire brush as appropriate.

Avoid emery cloth or grit-based abrasive papers. They leave deposits that the flux cannot remove and that cause porosity in the finished joint. A clean wire brush is the correct mechanical cleaning tool for silver brazing preparation.

Flux Selection and Application

Flux removes surface oxides from base metal surfaces during the heating cycle, leaving clean metal onto which the molten brazing alloy can wet and flow. Without effective flux coverage, even a correctly specified alloy at the right temperature will not flow properly.

Select the flux for your base metals and brazing temperature. GS30 general-purpose paste flux is correct for most standard silver brazing on copper, brass and mild steel (active to 800°C, FH10). For higher-temperature alloys, specify GSHT5 (active to 1000°C, FH20). For stainless steel, nickel alloys and tungsten carbide, Stay-Silv Black paste flux is required.

Apply flux generously and evenly to all joint surfaces before heating. Watch the flux during heating as a temperature guide — apply the brazing alloy when the flux is clear and flowing. Not before, when the flux is not yet active. Not after, when the flux may begin to exhaust.

Heating Technique

The objective of heating technique is to make the joint gap the hottest point in the assembly at the moment the alloy is applied. Silver brazing alloy flows towards heat — if the joint is the hottest point, the alloy will flow into it. If any adjacent area is hotter, the alloy will flow there instead.

Begin heating by warming the whole assembly broadly and evenly, moving the flame continuously rather than holding it in one position. Attempting to heat a cold, heavy component directly at the joint will result in the joint area overheating before the overall temperature is sufficient for brazing.

Apply the alloy to the joint — never to the flame. Heating the alloy in the flame causes overheating, burning of any flux coating, and loss of volatile alloy constituents. The alloy should flow freely into the joint by capillary action when applied to the correctly heated joint face.

Troubleshooting Common Brazing Problems

ProblemMost likely cause
Alloy flows freely but away from the jointHeating technique — joint gap is not the hottest point
Alloy melts but balls up and will not flowFlux problem — wrong flux, insufficient coverage, or overheating has exhausted the flux
Porous or incomplete joint fillJoint gap too wide, surface contamination, or insufficient alloy
Flux burns out before alloy flowsBurner too small or heating too slowly; flux active range exceeded
Joint looks sound but fails under loadIncomplete fill — alloy has not penetrated the full joint depth
Flux residue hard and resistant to water cleaningFlux has been overheated and devitrified

Frequently asked questions

What is the difference between brazing and soldering?

Both processes join metals using a filler metal that melts at a lower temperature than the base metals. The distinction is temperature: soldering uses filler metals with a liquidus below 450°C, brazing uses filler metals with a liquidus above 450°C. Silver brazing alloys typically braze between 600–800°C depending on grade. Brazed joints are considerably stronger than soldered joints and are used where structural integrity, pressure containment or high-temperature service is required.

What temperature does silver brazing require?

It depends on the alloy grade. Standard cadmium-free silver brazing alloys have liquidus temperatures ranging from approximately 660°C (AG103, 55% silver) up to around 800°C (lower silver content grades). As a rule, the higher the silver content, the lower the melting range. Most hand brazing work with a torch is carried out in the 650–750°C range. The flux colour change — from active and flowing to beginning to exhaust — is a reliable temperature guide in practice.

Do I need flux when brazing copper to copper?

It depends on the alloy. Silver copper phosphorus alloys (CP series) are self-fluxing on copper — the phosphorus content acts as a deoxidant and no separate flux is required for copper-to-copper joints. For all other alloy types, and for any joint involving brass, steel or other copper alloys, flux is required. Using a CP alloy on brass without flux is a common error and produces a poor, unreliable joint.

Why is my brazing alloy not flowing into the joint?

The most common cause is a flux problem — either the wrong flux for the application, insufficient flux coverage, or the flux has been exhausted by heating too slowly. The second most common cause is heating technique: if the area around the joint is hotter than the joint gap itself, the alloy will flow away from where you want it. Check your flux type and application first, then review your heat pattern.

What is the correct joint gap for silver brazing?

For most silver brazing applications, a gap of 0.05–0.2mm when cold is the recommended range. Within this range, capillary action draws the alloy reliably into the joint and produces a dense, sound fill. Gaps wider than 0.2mm produce weaker, less reliable joints. Remember that thermal expansion will change your gap at brazing temperature — design and fixture your joints to fall within the optimal range when hot, not just when cold.

Can I braze stainless steel?

Yes, but it requires the right flux. Standard paste fluxes (GS30, FH10) are not effective on stainless steel — the chromium oxide layer that forms on stainless requires a more aggressive flux. Stay-Silv Black paste flux is the correct specification for stainless steel, nickel alloys and tungsten carbide. For stainless-to-stainless or stainless-to-copper dissimilar joints, L-AG45SnSi with Stay-Silv Black is the standard recommendation.

How do I remove flux residue after brazing?

GS30 and most standard paste flux residues are water-soluble. Wash with warm water and a stiff brush while the joint is still warm but not hot enough to cause thermal shock. For stubborn residues or where flux has been overheated and devitrified, a dilute citric acid solution is effective. Remove residues promptly — flux left in contact with the base metal surface for extended periods can cause surface corrosion.

What silver content brazing alloy do I need?

For most general silver brazing on copper, brass and mild steel, a mid-range silver content alloy such as AG107 (30% silver) gives a good balance of performance and cost. For applications where joint ductility is important, where dissimilar metals are being joined, or where the lowest possible brazing temperature is needed, a higher silver content grade such as AG103 (55% silver) is the better choice. If you are unsure, contact us with your application details and we will advise on the correct specification.

Post-Braze Cleaning and Systematic Troubleshooting

Flux residues from GS30 and most standard paste fluxes are water-soluble. Remove with warm water and a stiff brush, or with a dilute citric acid solution. Remove residues promptly — flux left in place can be mildly corrosive to the base metal surface. Allow assemblies to cool in still air before quenching. Quenching before the alloy has fully solidified can disrupt the joint.

When a brazing problem appears in a production environment, resist the temptation to change multiple variables at once. Change one variable at a time — flux type, application method, heating technique, joint gap — and evaluate the result before making further changes. This approach identifies the root cause reliably and makes it possible to maintain consistent quality going forward.