Brazing Preforms Explained — When and Why to Use Them

Brazing Preforms Explained — When and Why to Use Them

What Are Brazing Preforms and When Should You Use Them?

For engineers working in low-volume or one-off fabrication, hand-feeding brazing rod is standard practice and works well. For production environments where the same joint is being brazed repeatedly — whether that is ten joints a shift or ten thousand — hand-feeding introduces variability that is difficult to control and even harder to measure. Preforms address that problem directly.

A brazing preform is a piece of brazing alloy cut, stamped or formed to a defined shape and weight, positioned in or around the joint before heating begins. When the assembly reaches brazing temperature, the preform melts and flows into the joint by capillary action, in the same way as hand-applied rod — but with the alloy quantity, position and distribution fixed in advance.

Types of Preforms

The most common preform forms are rings, washers, discs and strips, though preforms can be produced in almost any shape to suit a specific joint geometry.

Rings and collars are the standard preform for tubular joints — a copper pipe inserted into a fitting, for example. The ring sits around the tube at the mouth of the fitting before assembly. On heating, it melts and is drawn into the joint gap by capillary action. Ring preforms are available in a range of internal diameters and cross-sectional weights to suit different joint sizes and alloy requirements.

Washers and discs are used for flat lap joints and face joints, where the preform is placed between the two mating surfaces before assembly. The weight of the washer or disc is calculated to provide the correct volume of alloy for the joint area.

Custom preforms — cut to specific shapes from strip or foil — are produced for joints where a standard form does not suit the geometry. For complex or unusual joint configurations, we can produce preforms to customer drawings.

Why Preforms Improve Production Quality

The core advantage of preforms over hand-fed rod in production is consistency. Every joint receives exactly the same quantity of alloy, positioned in exactly the same location, every time. This eliminates two of the most common sources of joint-to-joint variability in production brazing: inconsistent alloy quantity and inconsistent alloy placement.

Excess alloy applied by hand-feeding produces large fillets, alloy waste and potential flow onto adjacent surfaces. Insufficient alloy leaves incomplete joint fill. With a preform of defined weight, neither of these outcomes occurs — the alloy quantity is matched to the joint requirement by design, not by operator judgement.

Preforms also remove the need for an operator to feed rod during the brazing cycle, which simplifies the heating operation and makes it easier to maintain the correct heat pattern. In automated or semi-automated brazing operations, this is essential — a robot or induction heating system cannot feed rod by hand.

Alloy Selection for Preforms

Preforms are available in all standard silver brazing alloys including the full AG range, copper phosphorus alloys and specialist grades. The alloy selection follows the same principles as for rod or wire — base metals, temperature range, joint strength requirements and cost all apply in the same way.

One consideration specific to preforms is that the alloy must have sufficient fluidity at brazing temperature to flow from the preform position into the joint gap. Alloys with narrow melting ranges and good fluidity — AG103 at 55% silver is the benchmark — perform best as preforms. Lower-silver grades with wider melting ranges and reduced fluidity can be used but may require more precise temperature control to ensure full joint fill.

Preforms in Automated Brazing

Induction brazing and furnace brazing are the two most common automated processes where preforms are standard rather than optional. Induction brazing heats the joint rapidly and precisely using an electromagnetic field — there is no practical way to introduce rod manually during the heating cycle, and the speed of induction heating means the alloy must already be in position. Preforms are the only viable approach for induction brazing.

Furnace brazing, where assemblies pass through a controlled-atmosphere furnace on a conveyor, similarly requires the alloy to be pre-placed before the heating cycle begins. Preforms, or in some cases brazing paste, are the standard alloy form for furnace processes.

Cost Considerations

Preforms cost more per kilogram than equivalent rod or wire, reflecting the additional processing involved in forming them to shape. The relevant comparison, however, is not cost per kilogram but cost per joint. When the reduction in alloy waste, the elimination of operator variability and the improvement in joint consistency are factored in, preforms typically reduce the total cost of the brazing operation in production environments even where the material unit cost is higher.

For low-volume or prototype work, the cost of producing custom preforms may not be justified — rod or wire remains the practical choice. For any production run where the same joint geometry is being brazed repeatedly, the economics of preforms are worth evaluating seriously.

Specifying Preforms

To specify a preform, we need the joint geometry (internal diameter for rings, face dimensions for washers and discs), the alloy grade, the required cross-sectional weight or volume of alloy per joint, and the quantity required. For complex joint geometries, a drawing or sample component is helpful. Contact our technical team to discuss your requirements and we will advise on the most appropriate preform form and alloy.

Contact our team for technical advice or to request a quote on brazing preforms.

Back to blog